The specific Galaxy S10 Plus Japan Firmware Download Package comes with a Stock ROM of Galaxy S10 Plus Japan. This helps you to bypass FRP lock and revert from the root and custom ROM.
Samsung S10 Plus Japan (SCV42 SC-04L) Firmware – Full Repair
There are various reasons to flash “Stock Firmware on Galaxy S10 Plus Japan“. For instance, if your phone gets stuck on the logo and you need to remove the FRP lock from it.
If you’re going to reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Fix boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs
- To solve the lag or stutter
- Fix software issues.
- Revert to stock firmware
Pre-requirements:
- Supported Phone: Galaxy S10 Plus Japan
- Ensure it’s at least 50% charged.
- Laptop or PC.
- Backup Android Phone
- Download and install the Samsung USB Driver
- Download Odin’s Latest version
Galaxy S10 Plus Japan Stock ROM Details:
FULL ROM SC04L DOWNLOAD |
||||||
AP VERSION | CSC VERSION | code | Type | OS | Size | link google |
SC04LOMU1BTE2 | SC04LDCM1BTE2 | DCM | FULL | 10 | 4,1G | DOWNLOAD |
SC04LOMU1BTB2 | SC04LDCM1BTB2 | DCM | FULL | 10 | 4,1G | DOWNLOAD |
SC04LOMU1BSLA | SC04LDCM1BSLA | DCM | FULL | 10 | 4,1G | DOWNLOAD |
SC04LOMU1ASJ6 | SC04LDCM1ASJ6 | DCM | FULL | OS9 | 3,8G | DOWNLOAD |
FULL ROM SCV42 DOWNLOAD |
||||||
AP VERSION | CSC VERSION | code | Type | OS | Size | link google |
SCV42KDU1BTE2 | SCV42QDI1BTE2 | KDI | FULL | 10 | 4,2G | DOWNLOAD |
SCV42KDU1BTB2 | SCV42QDI1BTB2 | KDI | FULL | 10 | 4,1G | DOWNLOAD |
SCV42KDU1ASJ6 | SCV42QDI1ASJ6 | KDI | FULL | OS9 | 3,9G | DOWNLOAD |
SCV42KDU1ASG1 | SCV42QDI1ASG1 | KDI | FULL | OS9 | 3,8G | DOWNLOAD |
SCV42KDU1ASF4 | SCV42QDI1ASF4 | KDI | FULL | OS9 | 3,8G | DOWNLOAD |
SCV42KDU1ASDB | SCV42QDI1ASDB | KDI | FULL | OS9 | 3,7G | DOWNLOAD |
How To Install Galaxy S10 Plus Japan Stock Firmware:
1: Download and Install Samsung USB Driver on your computer. If Samsung USB Driver is installed on your computer, Skip this Step.
2: Download and extract the Galaxy S10 Plus Japan Firmware files on your computer.
3: Now, Switch off your Smartphone.
4: Turn off the phone and boot into Download Mode.
Press and hold Volume Down, Home and Power button at the same time for 5-8 seconds until download mode is active.
5: In Download mode a Warning Yellow Triangle Sign appeares . Press Volume Up to proceed.
6: Now, Download and open Odin. Then connect your Smartphone to the computer.
7: Odin will detect the device and show the “Added message in the lower-left panel.”.
8: Once Odin detects your device, click the PDA button, and select the Firmware.tar file.
9: Click the Start button in Odin to begin the Flashing.
10: Flashing usually takes 30-50 seconds to complete the process on your Phone.
Once you see the Pass message in Odin, you can disconnect your device from the pc.
When your Galaxy S10 Plus Japan finally boots up, you should now be running your desired firmware.
To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”
Disclaimer:
- Read and understand the Full Guide before flashing.”Galaxy S10 Plus Japan Firmware“.
- Use these instructions at your own risk.
- Phone must have a 70–80% charge.