Multilaser M Pro 3G Firmware File [MT6577 Stock ROM]

if you are facing Multilaser M Pro 3G firmware issue. Then you can install ROM at home without any help of a software technician. in fact not all of the issues that are the hardware fault.

Today we will discuss how to sort out Multilaser M Pro 3G Stock Rom issue. There are several methods to Flash Multilaser M Pro 3G Firmware. Of course, there are also some custom mods and ROMs that you can try.

Multilaser M Pro 3G Firmware File

However, if you do not like the custom ROMs you have installed and want to go back to the original operating system, we have the guide for you.

If you are looking for this guide, we will now see how you can flash the stock firmware on Multilaser M Pro 3G.

We are going to Flash Stock ROM on Multilaser M Pro 3G. In this guide, we have used the SP Flash Tool to flash the Multilaser M Pro 3G Firmware.

And we include the Official link to Download Multilaser M Pro 3G Stock ROM and all Needed Files. your device may get bricked And flashing stock ROM is the only way to go out.

To perform this advance process of Flashing stock ROM please Go Step by step. If you got any error then leave a Comment.

We use the Sp flash tool for this procedure there are different reasons why we will use Sp Flash Tool to unbrick the Multilaser M Pro 3G. I believe this tool is very efficient.

Follow the step by step procedure to use One Click Unbrick Tool and unbrick your Multilaser M Pro 3G.

The Advantages Of Multilaser M Pro 3G Stock ROM:

A Soft Brick or a Software Brick, is usually just when you’re Multilaser M Pro 3G is stuck in a boot loop, and as the name implies, is caused by a software error on Multilaser M Pro 3G.

Usually the lack of a system to boot from or some other minor software bug that glitching boot.

They are easily fixable by flashing the stock ROM on Multilaser M Pro 3G through recovery or with SP Flash Tool.

If your Multilaser M Pro 3G device turns to a soft-brick, it may:

  • Keeps Rebooting;
  • Boots Straight Into Recovery;
  • Boots Straight Into its Bootloader;
  • Freeze at the startup screen or boot Animation;

Multilaser M Pro 3G Stock ROM Details:

Gapps File Included
Device Supported Multilaser M Pro 3G
Tool Supported SP Flash Tool
Processor MediaTek MT6577
Os Android
Download Multilaser_M_Pro_3_MT6577_080713.zip

Pre-requirements to Install Multilaser M Pro 3G Firmware:

  • Supported Phone: Multilaser M Pro 3G
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

1. Take Multilaser M Pro 3G Backup

Before going to install stock ROM you need to take all your messages, photos, and apps from your current smartphone. This requires a backup that you then restore on your device after flashing firmware.

Most smartphones automatically make a backup in the background, in case something happens. But to make sure you take everything to your new device, you need a full backup.

How To Backup Android Phone Before Flashing Stock Firmware


2. Download Multilaser M Pro 3G Flashing Tool And Drivers:

A.  Download and install MTK Drivers. This is for basic communication between your device and PC.

These drivers are mainly for the devices powered by MediaTek chipset. With these drivers, you can transfer files, flash the firmware files on the device, etc.

B. We use the Sp flash tool for this procedure there are different reasons why we will use Sp Flash Tool to unbrick the Multilaser M Pro 3G.

I believe this tool is very efficient. Follow the step by step procedure to use One Click Unbrick Tool and unbrick your Multilaser M Pro 3G.


Disclaimer:

  • Please Read and understand the Full Guide Before Flashing Multilaser M Pro 3G Firmware.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to you or your device, resulting from the use of information in this guide.
  • Before flashing, Stock ROM Multilaser M Pro 3G must have a 70–80% charge.

Don’t flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones, you will have a brick even if you download these blocks read from a phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.

Instructions to Install Multilaser M Pro 3G Firmware:

1. Download Multilaser M Pro 3G Firmware zip file given above and extract it in your computer.

2. Download Multilaser M Pro 3G USB driver and set up it on your computer. In case if in case you have already put in USB driver in your computer skip this step.

3. Next, switch off your Multilaser M Pro 3G smartphone and take away the battery (it’s removable).

4. Now go to the extracted folder in Step 1 and open up the SP Flash Tool sub-folder. You will discover “Flash_tool.exe” file in it. Launch it.

5. As soon as SP Flash tool is launched, click on on “Download” tab.

6. Now, click on on “Scatter-loading” button within the download tab.

7. Next, click on on “Open Scatter File” and choose the scatter file from Step 1. For reference see the picture given under.

8. Now click on on the “Download” button to start out the flashing process.

9. Next, join your Multilaser M Pro 3G Android device to your computer by means of the unique USB cable (without battery – whether it is battery removable) and press volume up or volume down button.

10. The flashing process will start momentarily, and it’ll get accomplished in a minute or two. As soon as it’s over, you will notice the “Download OK” green ring in SP Flash Tool.

11. Now, shut SP Flash tool in your computer and unplug your smartphone.

That’s it. Now you’ve successfully flashed Multilaser M Pro 3G stock ROM on your  Android device. If you happen to encounter any points whereas following this tutorial, do let me know by way of feedback.

Follow detailed Instruction to flash Multilaser M Pro 3G Firmware with Sp flash tool.

Leave a Reply

Your email address will not be published. Required fields are marked *