Doogee X20 Secure Boot DA File [Format Single Partition]

Doogee X20 Secure Boot DA File

Format A Single Partition In Doogee X20 using Doogee X20 Secure Boot DA File. This is a step by step guide showing how to format a single partition of a Doogee X20 using SP flash tool.

Why would I want to format a single partition on my Doogee X20?

There are different causes why one might want to format a single partition on a Doogee X20. One such example is when your device is FRP locked, all you need do is to format only FRP partition OR maybe you need to perform a factory reset but you are unable to boot into recovery mode for some weird unknown reasons, all you need is to format user data and cache partitions. The method below will show how we can do this.

Note:

1. open folder

2. extract flash tool and open flash tool

3. select da file in FRP folder

4. select scatter file

5. formate with FRP address ( 0x2d88000 0x100000 )

6. FRP done but dl image failed to show your screen

7. fix dl image failed flash with cache file job done.

FRP address
0x2d88000
0x100000

Requirements to format one single partition on my Doogee X20:

  • Supported Phone: Doogee X20
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC.

Take Doogee X20 Backup:

Download Doogee X20 Flashing Tool And Drivers:

Doogee X20 Secure Boot DA File Detail:

  • File Name: S4 IX626B Boot DA
  • Device Supported: Doogee X20
  • Tool Supported: Sp Flash Tool

Download

[quads id=2]

How to Format a Single Partition of Doogee X20:

1. The steps below explain how to format a single partition of a Doogee X20 using the SP flash tool.

2. Extract the content of the SP flash tool zip file and Launch SP flash tool.

Launch Sp Flash Tool to Format a Single Partition of Doogee X20

3. Select the scatter file for your device by clicking choose besides the scatter-loading file’s dropdown bar.

Select scatter to Format a Single Partition of Doogee X20

4. In the windows that appear next, navigate to and select the Doogee X20 scatter file.

select the Doogee X20 scatter file

5. You should now be taken back to the SP flash tool window, click on the Format tab.

Doogee X20 Secure Boot DA File [Format Single Partition]

6. Tick the checkbox beside “Manual format flash”

Doogee X20 Manual format flash

7. Open windows explorer and navigate to the location of the scatter file you selected earlier on then open it using Notepad++

8. Scroll down the contents of the scatter file till you get to the partition you wish to format [in my case, I’m trying to format FRP partition]

Doogee X20 format FRP partition

9. Input the values of Linear_start addr and partition_size into SP flash tool then Click on Start

Code:

Linear_start addr = Begin Address
partition_size    = Format Length
Doogee X20 addr and partition_size

10. Power off the phone (with the battery in) then connect to the PC via a USB cord. Once successful, you should get a green tick.

11. Now you can boot up the Doogee X20.

Disclaimer:

  • Once the SP flash tool has detected your device, avoid disconnecting till the task is complete as this might cause the Doogee X20 to go dead.
  • If you accidentally selected “Autoformat – Format all”, your device will go dead and you’ll need to flash full Doogee X20 stock ROM to revive the phone.
  • Avoid using a random Doogee X20 scatter file (even though its for your chipset) in the Sp flash tool. Just because a scatter file is for your chipset doesn’t mean it contains the same partition info. Formatting with a wrong scatter file could result in more problems than you initially intended to fix.
  • SP flash tool was created by MediaTek Inc. so credits to them for the tool.