Tecno F1 DA File [Format Single Partition]

Format A Single Partition In Tecno F1 using Tecno F1 DA File free download. This is a step by step guide showing how to format a single partition of a Tecno F1 using SP flash tool.

Tecno F1 Secure Boot DA File

Tecno F1 Secure Boot DA File [Format Single Partition]

There are different causes why one might want to flash a Tecno f1 da file. One such example is when your device is FRP locked we will use this file as Tecno F1 FRP reset file and flash using scatter file with sp flash tool.

All you need do is to format only FRP partition OR maybe you need to perform a factory reset but you are unable to boot into recovery mode for some weird unknown reasons, all you need is to format user data and cache partitions. The method below will show how we can do this.

Requirements To Flash Tecno F1 Da File:

  • Supported Phone: Tecno F1
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

Take Tecno F1 Backup:

Download Tecno F1 Flash Tool And Drivers:

How to Format a Single Partition of Tecno F1 With DA File:

1. The steps below explain how to format a single partition of a Tecno F1 using the SP flash tool.

2. Extract the content of the SP flash tool zip file and Launch SP flash tool.

Launch Sp Flash Tool to Format a Single Partition of Tecno F1

3. Select the scatter file for your device by clicking choose besides the scatter-loading file’s dropdown bar.

Select scatter to Format a Single Partition of Tecno F1

4. In the windows that appear next, navigate to and select the Tecno f1 FRP scatter file.

select the Tecno F1 scatter file

5. You should now be taken back to the SP flash tool window, click on the Format tab.

Tecno F1 Secure Boot DA File [Format Single Partition]

6. Tick the checkbox beside “Manual format flash”

Tecno F1 Manual format flash

7. Open windows explorer and navigate to the location of the scatter file you selected earlier on then open it using Notepad++

8. Scroll down the contents of the scatter file till you get to the partition you wish to format [in my case, I’m trying to format FRP partition]

Tecno F1 format FRP partition

9. Input the values of Linear_start addr and partition_size into SP flash tool then Click on Start


Linear_start addr = Begin Address
partition_size    = Format Length

Tecno F1 addr and partition_size

10. Power off the phone (with the battery in) then connect to the PC via a USB cord. Once successful, you should get a green tick.

11. Now you can boot up the Tecno F1.


  • Once the SP flash tool has detected your device, avoid disconnecting till the task is complete as this might cause the Tecno F1 to go dead.
  • If you accidentally selected “Autoformat – Format all”, your device will go dead and you’ll need to flash full Tecno F1 stock ROM to revive the phone.
  • Avoid using a random Tecno F1 scatter file (even though its for your chipset) in the sp flash tool. Just because a scatter file is for your chipset doesn’t mean it contains the same partition info. Formatting with a wrong scatter file could result in more problems than you initially intended to fix.
  • SP flash tool was created by MediaTek Inc. so credits to them for the tool.

Tecno F1 Secure Boot DA File Detail:

  • File Name: S4 IX626B Boot DA
  • Device Supported: Tecno F1
  • Tool Supported: Sp Flash Tool

Download Tecno F1 DA File Without Password

Check Also

Lava Z62 Tested DA File

Lava Z62 Tested DA File [Secure Boot Auth]

Format A Single Partition using Lava Z62 DA File. This is a step by step guide …

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.