How To Flash We T1 Firmware File [Stock ROM]

We T1 Firmware

Download We T1 Firmware ROM File If you have a We T1 smartphone and you want We T1 Stock ROM Firmware to solve your bricked device, then you definitely are in the best article/post.

We will guide for you to install the official We T1 Firmware Flash File on the device. This step is simple and straightforward to follow. We have listed the We T1 Flash File below.

Download the Stock ROM file to repair your We T1.

The Benefits Of We T1 Stock ROM:

  • Flash Stock To Unbrick your
  • Fix boot loop issue
  • Update and Downgrade 
  • Unroot or Fix Bugs on the phone
  • To solve the lag or stutter on
  • Fix software issues.
  • Revert back to stock to get your warranty.

We T1 Stock ROM Details:

  • Gapps File: Included
  • Device Supported: We T1
  • Tool Supported: SP Flash Tool
  • Processor: MediaTek –MT6737M
  • Os: Android 7.0 Nougat
 Download File   Description
      Download

We T1 flash file without password

 We T1 MT6737M 17012018 7.0.zip

MT6737M__WE__T1__WE_T1__7.0__alps-mp-n0.mp1-V1.0.2_esky6737m.35.n.zip

[quads id=2]

Pre-requirements to Flash We T1 Stock Firmware File :

  • Supported Phone: We T1
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

Take We T1 Backup:

We T1 Flashing Tool And Drivers:

Disclaimer:

  • Please read and understand the Full Guide Before Flashing We T1 Stock ROM.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to you or your device, resulting from the use of information in this guide.
  • Make sure that the USB drivers for your device are installed on the computer.
  • Your smartphone must have a 70–80% charge.
  • Make a backup copy of important data such as call logs, SMS, and other data, it is to if something goes wrong, your data is not affected.

Don’t flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones, you will have a brick even if you download these blocks read from a phone which you own!

Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.

Instructions to Install Firmware on We T1:

Step 1: Extract And Run SP flash tool.

Step 2: Install MTK  android USB drivers.

Step 3: Then download We T1 Flash File for your phone from below.

Step 4: Switch off mobile remove the battery (if removable) reinsert and plug the USB cable in the charging socket.

Step 5: Now open SP flash tool.exe.

Step 6: When SP flash tool open, go to download button in SP flash tool.

Step 7: In the download tab, click on the scatter load button.

Step 8: After locating the scatter tab, click on the download button.

Step 9: Now connect your smartphone with a USB cable and press volume up or volume down key for easy detection (remove and reinsert your phone battery if it is removable)

Step 10: When flashing is completed, a green ring will appear in SP flash tool.

Step 11: Close SP flash tool on your computer and unplug the phone.

Step 12: Power on the phone and enjoy.

Step 13: After the flashing process starts, it might take up to 5–10 minutes. So keep patience and wait.

Follow Detailed Instruction Flashing With Sp Flash Tool.

Update Log:

  • Added: MT6737M__WE__T1__WE_T1__7.0__alps-mp-n0.mp1-V1.0.2_esky6737m.35.n.zip
  • Added: We T1 flash file without password

3 comments

  1. the procedure is the same for all MTK phone but I recommend you to download the fresh file from here otherwise because this file is tested by me and working 100% ok.

Comments are closed.