Wiko Barry Firmware

The specific Wiko Barry Firmware comes with a Stock ROM of Wiko Barry. This helps you to bypass FRP lock and revert form root and custom ROM.

Advertisement

Why would you want to flash Firmware on your Wiko Barry? [Stock ROM]

There are various reasons to flash (Firmware on Wiko Barry).

For instance, if your phone gets stuck on the logo and you need to remove the FRP lock from it.  If you’re going to hard reset your phone and cannot access the recovery menu. But most of the problems and benefits that cause flashing stock ROM are below.

The Benefit Of Wiko Barry Firmware:

  • Flash Stock ROM to unbrick your Wiko Barry
  • Update and downgrade
  • Unroot or fix bugs on the phone
  • To solve the lag or stutter
  • Fix software issues.
  • Revert to stock to get your warranty
  • Keeps rebooting issue
  • If your phone boots straight into recovery
  • Phone boots straight into its bootloader

Wiko Barry Firmware Details:

  • Gapps: Included
  • Device Supported: Wiko Barry
  • Tool Supported: SP Flash Tool
  • Soc: MediaTek MT6572
  • Os:

Download: Wiko_Barry_V1213652_MT6572.zip

[quads id=2]

Requirements To Flash Wiko Barry Stock ROM:

  • Charge your mobile: Your phone may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

 Take Wiko Barry Full Backup

Before going to install Wiko Barry stock ROM you need to take a backup of all your messages, photos, and apps from your smartphone.

Most smartphones automatically make a backup in the background. But to make sure you take everything to your new device, you need a full backup.
Most smartphones back up automatically in the background in case of incidents. To ensure a complete transition to your new device, a full backup is necessary.

Download Wiko Barry Flash Tool And Drivers:

A.  Download and install Wiko Barry Drivers. The necessary communication between your device and PC.

These drivers are mainly for the devices powered by MediaTek chipset. With these drivers, you can transfer files, flash the firmware files on the device, etc.

B. We use the Sp flash tool for as Wiko Barry Flash Tool because of this tool is very efficient and support all kind of MTK phones.

Instructions to Flash Wiko Barry Stock ROM:

1. First of all Download the ‘Wiko Barry flash file zip‘ which is given above and extract it on your computer’s desktop. Also, download and extract the sp flash tool.

2. Then download the Wiko Barry USB driver and set up it on your computer. In case you have already installed the USB driver on your computer skip this step.

3. Next, switch off your smartphone and take away the battery (if it is removable).

4. Now go to the sp flash tool extract folder and launch it.

5. As soon as the SP Flash tool is launch, click on the Download tab.

6. Now, click on the Scatter-loading button within the download tab.

7. Choose the scatter file from the Wiko Barry firmware extract folder.

8. Now click on the Download button to start the flashing process.

9. Next, connect your phone to your computer using the USB cable (without battery – if the battery is removable) and press volume up or volume down button at the same time.

10. The flashing process will start momentarily, and it’ll get accomplished in a minute or two.

As soon as it’s over, you will notice the Download OK green ring in SP Flash Tool.

Now, close the SP Flash tool and unplug your smartphone.

That’s it. Now you’ve successfully flashed stock ROM on your Wiko Barry.

Follow Detailed Instruction To Flash Wiko Barry Firmware With Sp Flash Tool.

Disclaimer:

  • Read and understand the Full Guide before flashing.”Wiko Barry Firmware”.
  • Use these instructions at your own risk.
  • Before flashing, Stock ROM on Wiko Barry must have a 70–80% charge.

Don’t flash another preloader and DSP_BL blocks! It is always dangerous! On some models of MTK phones, you will have a brick even if you download these blocks read from a phone which you own!

Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.

2 COMMENTS

  1. Hi Bro.
    Im trying to flash a wiko Barry death. All is OK with drivers. But when I start flash, after 6 sec appears an error. Brom?? (008) after purple color bar. I tried also with single files an the only one that works is preloaded. It is the lonely that goes to the end with green V.
    For all others I have same error. I checked memory and the results are OK.
    I don’t know how to solve this problem.
    I can’t charge battery. I can’t go in recovery. Nothing.
    Please help me if you can.
    I can’t find any help online about this error.
    Thank you for your time
    Marco

Comments are closed.