How To Flash Karbonn K9 Smart Plus Firmware Stock ROM

Karbonn K9 Smart Plus Firmware

 

I am flashing stock firmware on Karbonn K9 Smart Plus using the SPD Upgrade Tool. Step by step guide showing how to flash Karbonn K9 Smart Plus stock ROM with SPD Upgrade Tool.

Why would you want to flash Stock ROM on your Karbonn K9 Smart Plus?

There are various reasons to flash stock ROM on Karbonn K9 Smart Plus. For example, your phone will be stuck or hang on the logo. You want to remove FRP lock from it.  If you’re going to reset your phone hard and you cannot access the recovery menu. But most of the problems that cause flashing stock ROM are.

  • Flash Stock ROM To Unbrick
  • Update and downgrade
  • Unroot or fix bugs on the phone
  • To solve the lag or stutter
  • Fix software issues.
  • Revert to stock to get your warranty
  • Keeps rebooting issue
  • if your phone boots straight into recovery
  • Phone boots straight into its bootloader

[quads id=2]

Requirements to flash Karbonn K9 Smart Plus Stock ROM:

  • Supported Phone: Karbonn K9 Smart Plus
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC.

1. Take Karbonn K9 Smart Plus Backup

Before going to install Karbonn K9 Smart Plus stock ROM, you need to take all your messages, photos, and apps from your current smartphone. This requires a backup that you then restore on your device after flashing firmware.

How To Backup Android Phone Before Flashing Stock Firmware

2. Download Karbonn K9 Smart Plus Flash Tool And Drivers:

A.  Download and install Karbonn K9 Smart Plus Drivers. The basic communication between your device and PC.

These drivers are mainly for the devices powered by MediaTek chipset. With these drivers, you can transfer files, flash the firmware files on the device, etc.

B. We use the SPD Upgrade Tool for as Karbonn K9 Smart Plus Flash Tool this procedure there are different reasons why we will use Sp Flash Tool to unbrick the Karbonn K9 Smart Plus.

I believe this tool is very efficient. Follow the step by step procedure to use One Click Unbrick Tool and unbrick your Karbonn K9 Smart Plus.

Karbonn K9 Smart Plus Stock ROM Details:

  • Gapps File: Yes
  • Device Supported: Karbonn K9 Smart Plus
  • Tool Supported: SPD Upgrade Tool
  • Soc: Spreadtrum
  • Android ver: Android

Download

[quads id=2]

Instructions to Install Karbonn K9 Smart Plus Firmware:

  1. Install Spreadtrum Drivers.
  2. Install the SPD Download Tool.
  3. Open the Research download tool > bin folder.
  4. Launch ResearchDownload.exe.
  5. Click on the Load Packet icon (top left corner).
  6. In the window that pops up, navigate to the location of the Karbonn K9 Smart Plus Firmware.pac file, select it then click Open.
  7. The PAC file should now be loaded (its name should appear at the top).
  8. Click the Settings Icon (top left corner).
  9. In the box that pops up, untick any item(s) you do not wish to flash then click OK. Ignore this step if you want to flash all files.
  10. Click the Start downloading button.
  11. You should see Waiting under the Progress bar.
  12. Switch off the phone (still with battery inside) then connect it to the PC via USB cord (note that you might need to hold the volume decrease button while connecting to PC on some phones) and flashing should begin. DO NOT interrupt.
  13. Once flashing is complete, you’ll see Passed.
  14. Click on the Stop downloading icon then disconnect the phone from PC and boot.

Follow Detailed Instruction Karbonn K9 Smart Plus Firmware Flashing With SPD Upgrade Tool.

Disclaimer:

  • Please read and understand the Full Guide Before Flashing Karbonn K9 Smart Plus Stock ROM.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to you or your device, resulting from the use of information in this guide.
  • Make sure that the USB drivers for your device are installed on the computer.
  • Your smartphone must have a 70–80% charge.
  • Make a backup copy of relevant data such as call logs, SMS, and other data; it is to if something goes wrong, your data is not affected.

Bin Packet load Error When Flashing Karbonn K9 Smart Plus Firmware: If you ever got Bin Packet Error then simply download and try flashing the firmware with this version of SPD Upgrade Tool.

How to Write IMEI After Flashing Karbonn K9 Smart Plus Firmware: After flashing the stock firmware on Spreadtrum Device, you may need to flash the IMEI also, for that use WriteIMEI on Spreadtrum Devices.