How to Pair Haylou GT7 Neo Earphones – Android / iOS / Pc

Pair Haylou GT7 Neo Earphones

Learn how to Pair Haylou GT7 Neo headphones. Check out all the steps to pair the headphones. Understand how the headphone’s touch controls work to perform each function. Finally, also see how to perform a factory reset (reset) on the headphones if they are experiencing connection problems.

Haylou’s GT series headphones are excellent products. The global version of the Haylou GT7 Neo has noise reduction that reduces audio delay in games. With good autonomy of use, the headphones are capable of playing for up to 5.5 hours, but this can vary depending on the volume of the music. Its functions are summarized as: playing / pausing music, changing previous/next song, answering/rejecting calls, call noise reduction, and voice assistant.

How to pair Haylou GT7 Neo headphones?

Before starting, check that the headphones have enough power to carry out the process. During the procedure, try to leave the devices close to each other.

These steps can be used to pair Haylou GT7 Neo headphones on both Android phones and tablets, as well as iOS devices (iPhone/iPad). Check out all the steps below:

Android / iOS:

  1. Access your cell phone’s Bluetooth. Enable it if it is disabled
  2. Then remove the earbuds from inside the charging case so that they turn on and connect with each other.
  3. In the Bluetooth “Available Devices” section, tap “Haylou GT7”.
  4. In the pop-up window that opens, tap “Pair”, “Connect” or “Pair” (the name displayed will depend on your device) and wait for the process to complete.
  5. That is all!

Pair Haylou GT7 Neo Windows PC/Notebook:

Pair Haylou GT7 Neo Windows PC/Laptop:

  1. Make sure your device’s Bluetooth is turned on.
  2. Then access “Settings”, located in the “Start” menu.
  3. Select the “Bluetooth and other devices” option.
  4. Click “Add Device”.
  5. Now click on “Bluetooth”.
  6. Take the earbuds out of the charging case.
  7. Wait for the headphones to turn on and connect with each other.
  8. From the list of available devices, select “Haylou GT7”.
  9. If prompted for a password, enter “0000” in the field.
  10. Wait for the pairing to complete.

Done! Your Haylou GT7 Neo headphones are now connected to your computer.

How to control the functions of the Haylou GT7 Neo headphones?

After completing the above step, you probably want to know how to use the functions of your new headphones. Below, you can check how to answer a call, control a song being played, and also activate some features.

functions of the Haylou GT7 Neo headphones

See which commands you should use to perform a certain task:

  • Power on: Remove the headphones from inside the case or press and hold the headphone button for 1.5 if they are off.
  • Power off: Press the earbud for 4.5s or put the earbuds into the case.
  • Play / Pause music: 1 short press left/right earphone.
  • Skip to the next song: 2 taps on the right earphone.
  • Answer / hang up a call: 1 short tap on the left/right earphone.
  • Activate voice assistant: 3 taps on left/right earphones.
  • Enable/disable low latency mode: 2 taps on the left earbud.

How to reset Haylou GT7 Neo headphones?

Connection problems or headphone sound? If you are experiencing this, maybe a factory reset on the headphones will solve your problem. To do this, see the steps you must follow below:

  1. First, go to your cell phone’s Bluetooth, tap on the name of the phone and select the option “remove, forget or cancel pairing. Then leave Bluetooth off.
  2. With the headphones already disconnected from the cell phone, place them inside the charging case and press and hold their touch area at the same time, for approximately 10 seconds.
  3. The lights on the 2 earbuds will flash repeatedly and then stay on. When this happens, it means that the reset was successful.

After that, just activate the cell phone’s Bluetooth again and perform a new pairing with your device.

Leave a Reply

Your email address will not be published. Required fields are marked *