Download Samsung firmware for device Galaxy Note10 SM-N970F with region XEC Spain. This firmware has version numbers PDA N970FXXU7GVA5 and CSC N970FOTF7GVB1. The operating system of this firmware is Android 12 S
Samsung Galaxy Note10 SM-N970F Firmware For Spain (Region XEC)
There are various reasons to flash “Stock Firmware“. For example, your phone will be stuck or hang on the logo. You want to remove the FRP lock from it.
If you’re going to hard reset your phone and you cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Flash Stock ROM to solve the boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs on the phone
- To solve the lag or stutter
- By flashing Stock ROM, you can fix software issues.
- Revert back to stock to get your warranty.
Pre-requirements:
- Supported Phone: SM-N970F Spain (Region XEC )
- Charge your mobile: You may no less than a half charge.
- Laptop or PC: To execute this installation, you must use a PC or Laptop.
- Backup Android Phone
- Download and install Samsung USB Driver
- Download Odin’s Latest version
Firmware Details:
Galaxy Note10 SM-N970F Spain – (Region XEC) Android 12 Firmware Updates:
Galaxy Note10 SM-N970F XEC PDA N970FXXU7GVA5:
| Model | SM-N970F |
| Name | Galaxy Note10 |
| Region | XEC – Spain |
| OS Version | Android 12 S |
| PDA | N970FXXU7GVA5 |
| CSC | N970FOTF7GVB1 |
| MODEM | N970FXXU7GVA1 |
| Size | 5.59 GB |
| changelist | 23301345 |
| build date | 2022-01-13 |
| Security Patch Level | 2022-01-01 |
| binary | 7 |
| Download | Google Drive |
Galaxy Note10 SM-N970F XEC PDA N970FXXU7GULD:
| Model | SM-N970F |
| Name | Galaxy Note10 |
| Region | XEC – Spain |
| OS Version | 12 S |
| PDA | N970FXXU7GULD |
| CSC | N970FOTF7GULD |
| MODEM | N970FXXU7GUL7 |
| Size | 5.59 GB |
| changelist | 23301345 |
| build date | 2021-12-24 |
| Security Patch Level | AT |
| binary | 7 |
| Download | Google Drive |
Galaxy Note10 SM-N970F Spain – (Region XEC) Android 11 Firmware Updates:
How To Install Samsung Stock Firmware:
Download the Odin and USB Drivers on your PC. Follow the below link to install the firmware using the Odin Flash tool.
How To Flash Samsung Stock Firmware With ODIN
1: Download and Install Samsung USB Driver on your computer. If Samsung USB Driver is already installed on your computer, then Skip this Step.
2: Download and extract the Galaxy Note10 SM-N970F Firmware For Spain (Region XEC ) files on your computer.
3: Now, Switch off your Smartphone.
4: After switching off the phone, you need to boot into Download Mode. To boot into download mode.
Press and hold Volume Down, Home, and Power button at the same time for 5-8 seconds until download mode is active.
5: In the Download mode, you will be able to see a Warning Yellow Triangle Sign. In this situation, you have to press the Volume Up key to continue.
6: Now, Download and open Odin. Then connect your Smartphone to the computer.
7: Once you have connected the Smartphone to the computer, Odin will automatically recognize the device and show the “Added” message at the lower-left panel.
8: Once Odin detects your device, click on the PDA button, and select the Firmware.tar file.
9: Now, click on the Start button in Odin to begin the Flashing.
10: Flashing usually takes 30-50 seconds to complete the process on your Phone.
Once the Firmware process is completed you will be able to see a Green Box with Pass written on it in Odin. During this process, the Smartphone will reboot automatically.
Once you see, the Pass message in Odin, you can disconnect your Device from the computer.
The flashing process will begin and should take about 10–12 minutes. It may take some time for your device to reboot, but don’t be alarmed.
When your phone finally boots up, you should now be running your desired firmware.
If you want to check that the correct firmware is installed, head to Settings –> About Phone –> Software Information. The firmware number is located under the “Baseband version.”
Disclaimer:
- Please read and understand the Full Guide before flashing “Stock Firmware“.
- Use these instructions at your own risk. We will not be responsible for everything that happens to your device, resulting from the use of information in this guide.
- Before flashing, Stock ROM must have a 70–80% charge.
