Motorola XT1760 Secure Boot DA File [Format Single Partition]

Format A Single Partition In Motorola XT1760 using Motorola XT1760 Secure Boot DA File. This is a step by step guide showing how to format a single partition of a Motorola XT1760 using SP flash tool.

Motorola XT1760 Secure Boot DA File

Why would I want to format a single partition on my Motorola XT1760?

There are different causes why one might want to format a single partition on a Motorola XT1760. One such example is when your device is FRP locked, all you need do is to format only FRP partition OR maybe you need to perform a factory reset but you are unable to boot into recovery mode for some weird unknown reasons, all you need is to format user data and cache partitions. The method below will show how we can do this.

Requirements to format one single partition on my Motorola XT1760:

  • Supported Phone: Motorola XT1760
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

Take Motorola XT1760 Backup:

Download Motorola XT1760 Flashing Tool And Drivers:

Motorola XT1760 Secure Boot DA File Detail:

  • File Name: S4 IX626B Boot DA
  • Device Supported: Motorola XT1760
  • Tool Supported: Sp Flash Tool

Download

XT1760 Da Boot File .zip

How to Format a Single Partition of Motorola XT1760:

1. The steps below explain how to format a single partition of a Motorola XT1760 using SP flash tool.

2. Extract the content of the SP flash tool zip file and Launch SP flash tool.

Launch Sp Flash Tool to Format a Single Partition of Motorola XT1760

3. Select the scatter file for your device by clicking choose besides the scatter-loading file’s dropdown bar.

Select scatter to Format a Single Partition of Motorola XT1760

4. In the windows that appear next, navigate to and select the Motorola XT1760 scatter file.

select the Motorola XT1760 scatter file

5. You should now be taken back to the SP flash tool window, Click on the Format tab.

Motorola XT1760 Secure Boot DA File [Format Single Partition]

6. Tick the checkbox beside “Manual format flash”

Motorola XT1760 Manual format flash

7. Open windows explorer and navigate to the location of the scatter file you selected earlier on then open it using Notepad++

8. Scroll down the contents of the scatter file till you get to the partition you wish to format [in my case, I’m trying to format FRP partition]

Motorola XT1760 format FRP partition

9. Input the values of Linear_start addr and partition_size into SP flash tool then Click on Start

Code:

Linear_start addr = Begin Address
partition_size    = Format Length

Motorola XT1760 addr and partition_size

10. Power off the phone (with the battery in) then connect to the PC via a USB cord. Once successful, you should get a green tick.

11. Now you can boot up the Motorola XT1760.

Disclaimer:

  • Once SP flash tool has detected your device, avoid disconnecting till the task is complete as this might cause the Motorola XT1760 to go dead.
  • If you accidentally selected “Autoformat – Format all”, your device will go dead and you’ll need to flash full Motorola XT1760 stock ROM to revive the phone.
  • Avoid using a random Motorola XT1760 scatter file (even though its for your chipset) in Sp flash tool. Just because a scatter file is for your chipset doesn’t mean it contains the same partition info. Formatting with a wrong scatter file could result in more problems than you initially intended to fix.
  • SP flash tool was created by MediaTek Inc. so credits to them for the tool.

Check Also

Infinix X653C DA File

Infinix X653C DA File [Secure Boot Auth]

Format A Single Partition using Infinix X653C DA File. This is a step by step …

Leave a Reply

Your email address will not be published. Required fields are marked *