How To Fix Lenovo Tab 3 710i Dead After Flash Only Vibrates

Lenovo Tab 3 710i is one of the world’s cheapest tablets. But cheaper as well as some software issues. For example, if it has more applications or games installed or its internal storage is full, then it gives a lot of error like unfortunately, the system has stopped working.

In addition, whenever the user connects to the Internet, different types of viruses come. Due to these problems, the user is often hard reset and it is funny that the virus still does not leave.

If you have a little bit of information about flashing the mobile, then you can try the below method to flash your  Lenovo Tab 3 710i with official stock firmware.

if you already install Lenovo Tab 3 710i firmware and your Lenovo tb3-710i dead after flash you are receiving an error such as. your tablet is not turning on and only vibrates. Or

“4032  Error ” and the flash will not start

How To Fix Lenovo Tab 3 710i Dead After Flash Only Vibrates

The Advantages Of Lenovo Tab 3 710i Stock ROM:

A Soft Brick or a Software Brick, is usually just when you’re Lenovo Tab 3 710i is stuck in a boot loop, and as the name implies, is caused by a software error on Lenovo Tab 3 710i.

Usually the lack of a system to boot from or some other minor software bug that glitching boot.

They are easily fixable by flashing the stock ROM on Lenovo Tab 3 710i through recovery or with SP Flash Tool.

If your Lenovo Tab 3 710i device turns to a soft-brick, it may:

  • Keeps Rebooting;
  • Boots Straight Into Recovery;
  • Boots Straight Into its Bootloader;
  • Freeze at the startup screen or boot Animation;

Lenovo Tab 3 710i Stock ROM Details:

Gapps File: Included
Device Supported: Lenovo Tab 3 710i
Tool Supported: SP Flash Tool
Processor: MediaTek MT6580
Os: Android
Download: MT6580 Lenovo TB3-710I 5.1 USR S110043 1703011200 MP6V2 MOE.zip

Pre-requirements to Install Lenovo Tab 3 710i Firmware:

  • Supported Phone: Lenovo Tab 3 710i
  • Charge your mobile: You may no less than a half charge.
  • Laptop or PC: To execute this installation, you must use a PC or Laptop.

1. Take Lenovo Tab 3 710i Backup

Before going to install stock ROM you need to take all your messages, photos, and apps from your current smartphone. This requires a backup that you then restore on your device after flashing firmware.

Most smartphones automatically make a backup in the background, in case something happens. But to make sure you take everything to your new device, you need a full backup.

How To Backup Android Phone Before Flashing Stock Firmware


2. Download Lenovo Tab 3 710i Flashing Tool And Drivers:

A.  Download and install MTK Drivers. This is for basic communication between your device and PC.

These drivers are mainly for the devices powered by MediaTek chipset. With these drivers, you can transfer files, flash the firmware files on the device, etc.

B. We use the Sp flash tool for this procedure there are different reasons why we will use Sp Flash Tool to unbrick the Lenovo Tab 3 710i.

I believe this tool is very efficient. Follow the step by step procedure to use One Click Unbrick Tool and unbrick your Lenovo Tab 3 710i.


Disclaimer:

  • Please Read and understand the Full Guide Before Flashing Lenovo Tab 3 710i Firmware.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to you or your device, resulting from the use of information in this guide.
  • Before flashing, Stock ROM Lenovo Tab 3 710i must have a 70–80% charge.

Don’t flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones, you will have a brick even if you download these blocks read from a phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.

Instructions to Install Lenovo Tab 3 710i Firmware [Lenovo tb3-710i dead after flash]:

1. Download Lenovo Tab 3 710i Firmware zip file given above and extract it in your computer.

2. Download Lenovo Tab 3 710i USB driver and set up it on your computer. In case if in case you have already put in USB driver in your computer skip this step.

3. Next, switch off your Lenovo Tab 3 710i smartphone and take away the battery (it’s removable).

4. Now go to the extracted folder in Step 1 and open up the SP Flash Tool sub-folder. You will discover “Flash_tool.exe” file in it. Launch it.

5. As soon as SP Flash tool is launched, click on on “Download” tab.

6. Now, click on on “Scatter-loading” button within the download tab.

7. Next, click on on “Open Scatter File” and choose the scatter file from Step 1. For reference see the picture given under.

8. Now click on on the “Download” button to start out the flashing process.

9. Next, join your Lenovo Tab 3 710i Android device to your computer by means of the unique USB cable (without battery – whether it is battery removable) and press volume up or volume down button.

10. The flashing process will start momentarily, and it’ll get accomplished in a minute or two. As soon as it’s over, you will notice the “Download OK” green ring in SP Flash Tool.

11. Now, shut SP Flash tool in your computer and unplug your smartphone.

That’s it. Now you’ve successfully flashed Lenovo Tab 3 710i stock ROM on your  Android device. If you happen to encounter any points whereas following this tutorial, do let me know by way of feedback.

Follow detailed Instructions to flash Lenovo Tab 3 710i Firmware with Sp flash tool.

1 Comment

  1. my tabe is 710 i
    buy its mt8321
    not mt6580
    and sp keep refuse mt6580
    and i cant find mt8321
    i did try many sp flash versin
    any advaice please

Write A Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.