Galaxy Tab S6 Wi-Fi SM-T860 U4 Firmware – Android 12 S
The specific Galaxy Tab S6 Wi-Fi SM-T860 U4 Firmware Download Package comes with a Stock ROM of Galaxy Tab S6 Wi-Fi SM-T860 U4 Security Patch Level 2022-02-01 (February 2022). This helps bypass the FRP lock and revert from the root and custom ROM.
Samsung Galaxy Tab S6 Wi-Fi SM-T860 Binary 4 Firmware – Android 12 S – DBT – T860XXU4DVC3 – Germany
There are various reasons to flash “Stock Firmware on Galaxy Tab S6 Wi-Fi SM-T860 U4“. For example, your Phone will be stuck or hang on the logo. You want to remove the FRP lock from it.
Suppose you will reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Fix boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs on the Phone
- To solve the lag or stutter
- Fix software issues.
- Revert to stock firmware
Pre-requirements:
- Supported Phone: Galaxy Tab S6 Wi-Fi SM-T860 U4
- Ensure it’s at least 50% charged.
- Laptop or PC.
- Backup Android Phone
- Download and install the Samsung USB Driver
- Download Odin’s Latest version
Galaxy Tab S6 Wi-Fi SM-T860 U4 Stock ROM Details:
SM-T860 U4 Firmware – DBT – T860XXU4DVC3 – Germany:
| Model | SM-T860 Binary 4 U4, S4, Bit 4 |
| Region / Country | Germany |
| Language | Multi-Language |
| Android version | Android 12 S |
| Operator / Carrier | Clean (no logo, operator apps) |
| AP / PDA | T860XXU4DVC3 |
| CSC | T860OXM4DVC3 |
| MODEM CP Version | – |
| product code | DBT |
| Build Date | 20220312121200 |
| Security Patch Level | 2022-02-01 (February 2022) |
| Size | 6.43 GB Full Files |
| Download | Google Drive | Android File Host |
How To Install Galaxy Tab S6 Wi-Fi SM-T860 U4 Stock Firmware:
1: Install the Samsung USB Driver on your pc.
2: Download and extract the Galaxy Tab S6 Wi-Fi SM-T860 U4 Firmware files on your computer.
3: Now, Switch off your Smartphone.
4: After switching off the Phone, you need to boot into Download Mode. To boot into download mode.
Press and hold Volume Down, Home, and Power button at the same time for 5-8 seconds until download mode is active.
5: A Warning Yellow Triangle Sign appears in Download mode. Press the Volume Up key to proceed.
6: Open Odin. Then, connect your phone to the pc.
7: Odin will detect the device and show the “Added message in the lower-left panel.”.
8: Click the PDA button and select the Firmware.tar file.
9: Now, click the Start button in Odin to begin the Flashing.
10: Flashing usually takes 30-50 seconds to complete on your Phone.
Once the Firmware process is completed, you can see a Green Box with Pass written in Odin. During this process, the Smartphone will reboot automatically.
Once you spot the “Pass” message in Odin, you can unplug your device from the computer.
You should run your desired firmware when your Galaxy Tab S6 Wi-Fi SM-T860 U4 finally boots up.
To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”
Disclaimer:
- Read and understand the Full Guide before flashing.”Galaxy Tab S6 Wi-Fi SM-T860 U4 Firmware“.
- Use these instructions at your own risk. We are not liable for any outcomes on your device due to following the information in this guide.
- Phone must have a 70–80% charge.
