Galaxy S9 + SM-G9650 U9 Firmware – G9650ZHS9FUC8
The specific Galaxy S9 + SM-G9650 U9 Firmware Download Package has a Stock ROM of Galaxy S9 + SM-G9650 U9 Security Patch Level 2022-05-01 (May 1, 2022). This helps bypass FRP lock and revert from the root and custom ROM.
Samsung Galaxy S9+ SM-G9650 Binary 9 Android 10 Q Brazil ZTO G9650ZHU9FVF2
There are various reasons to flash “Stock Firmware on Galaxy S9 + SM-G9650 U9“. For example, your Phone will be stuck or hang on the logo. You want to remove the FRP lock from it.
Suppose you’re going to reset your Phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Fix boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs on the Phone
- To solve the lag or stutter
- Fix software issues.
- Revert to stock firmware
Pre-requirements:
- Supported Phone: Galaxy S9 + SM-G9650 U9
- Charge your mobile: You may no less than a half charge.
- Laptop or PC: To execute this installation, you must charge using a PC or Laptop.
- Backup Android Phone
- Download and install Samsung USB Driver
- Download Odin’s Latest version
Galaxy S9 the + SM-G9650 U9 Stock ROM Details:
SM-G9650 U9 Brazil ZTO G9650ZHU9FVF2:
Model | SM-G9650 Binary 9 U9, S9, Bit 9 |
Region / Country | Brazil |
Language | Multi-Language |
Android version | Android 10 Q |
Operator / Carrier | Clean ZTO (no logo, carrier apps) |
AP / PDA | G9650ZHU9FVF2 |
CSC | G9650OWO9FVF2 |
CP Version / Baseband Modem | G9650ZCU9FVE3 |
product code | ZTO |
Build Date | 2022-06-30 |
Security Patch Level | 2022-05-01 (May 1, 2022) |
Size | 4.2 GB |
Brazil – ZTO | Mega | Google Drive |
Panama – TPA | Mega | Google Drive |
Brazil – Vivo ZVV | Mega | Google Drive |
How To Install Galaxy S9 + SM-G9650 U9 Stock Firmware:
1: Download and Install Samsung USB Driver on your computer. If Samsung USB Dthe River is installed on your computer, Skip this Step.
2: Downlnd extract the Galaxy S9 + SM-G9650 U9 Firmware files on your computer.
3: Now, Switch off your Smartphone.
4: After switching off the Phone, you need to boot into Download Mode. To boot into downloads
Press and hold Volume Down, Home and Power button at the same time for 5-8 seconds until download mode is active.
5: In the Download mode, you will download a Warning YelloSign. In this situation, you have to press the Volume Up key to continue.
6: Now, Download and open Odin. Then, move your Smartphone to the computer.
7: Once you have connected the Smartphone to the computer, the Smartphone automatically recognizes the Device and shows the “Added” message in the lower-left panel.
8: Once Odlower leaves your Device, click the PDA button and select the Firmware.tar file.
9: Click the Start button in Odin to begin the Flashing.
10: Flashing usually takes 30 seconds on your Phone to complete t
Once the Firmware process is completed, you can see a Gre, en Bcanitten on it in Odin. During this process, the Smartphone will reboot automatically.
Once you see the Pass message in Odin, you can disconnect your device from the pc.
The flashing process will begin and should take about 10–12 minutes. It may take some time for your device device to reboot, bmed.
When your Galaxy S9 + SM-G9650 finally boots up, you should now be running your desired ware.
To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”
Disclaimer:
- Read and understand the Full Guide before flashing.”Galaxy S9 + SM-G9650 U9 Firmware“.
- Use these instructions at your own risk. We will not be responsible for everything that happens to your Device resulting from using the information in this guide.
- Phone must have a 70–80% charge.