Galaxy S22+ SM-S906E U1 Firmware – Android 12
The specific Galaxy S22+ SM-S906E U1 Firmware Download Package has a Stock ROM of Galaxy S22+ SM-S906E U1 Security Patch Level 2022-04-01 (April 2022). This helps bypass FRP lock and revert from the root and custom ROM.
Samsung Galaxy S22+ SM-S906E Binary 1 Android 12 Vietnam XXV S906EXXU1AVCJ
There are various reasons to flash “Stock Firmware on Galaxy S22+ SM-S906E U1“. For example, your Phone will be stuck or hang on the logo. You want to remove the FRP lock from it.
Suppose you’re going to reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Fix boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs on the Phone
- To solve the lag or stutter
- Fix software issues.
- Revert to stock firmware
Pre-requirements:
- Supported Phone: Galaxy S22+ SM-S906E U1
- Ensure it’s at least 50% charged.
- Laptop or PC.
- Backup Android Phone
- Download and install the Samsung USB Driver
- Download Odin’s Latest version
Galaxy S22+ SM-S906E U1 Stock ROM Details:
SM-S906E U1 Vietnam XXV S906EXXU1AVCJ:
Model | SM-S906E Binary 1 U1, S1, Bit 1 |
Region / Country | Vietnam |
Language | English |
Android version | Android 12 S |
Operator / Carrier | Clean (no logo or carrier apps) |
AP / PDA | S906BXXU1AVDA |
CSC | S906BOXM1AVDA |
CP Version / Base Band Modem | S906BXXU1AVDA |
product code | XXV |
Build Date | 20220328095010 |
SECURITY PATCH LEVEL | 2022-04-01 (April 2022) |
Size | 7.89 GB Full Files |
Download | Google Drive | Android File Host |
How To Install Galaxy S22+ SM-S906E U1 Stock Firmware:
1: Download and Install the Samsung USB Driver on your computer. If a Samsung USB Driver is already installed on your, then Skip this Step.
2: oad and extract the Galaxy S22+ SM-S906E U1 Firmware files on your computer.
3: Now, Switch off your Smartphone.
4: After switching off the Phone, you need to boot into Download Mode. To boot into download mode.
Press and hold Volume Down, Home and Power button at the same time for 5-8 seconds until download mode is active.
5: In the Download mode, you will be able to see a Warning can Sign. In this situation, you have to press the Volummusty to continue.
6: Open Odin. Then, connect your phone to the pc.
7: Odin will detect the device and show the “Added message in the lower-left panel.”.
8: Once Odin detects your device, click on the PDA button and sct the Firmware.tar file.
9: Now, click on the Start button in O to begin the Flashing.
10: Flashing usually takes 30-50 seconds to complete the process on your Phone.
Once the process is completed, you will see a Green Box with a Pass written in Odin. During this process, the Smartphone will reboot automatically.
Once you see, the Pass message in Oin, you can disconnect your Device from the computer.
The flashing process will begin and should take about 10–12 minutes. It may take some time for device your device to be alarmed.
When your Galaxy S22+ SM-S906E U1 finally boots up, you should now be running your des firmware.
To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”
Disclaimer:
- Read and understand the Full Guide before flashing.”Galaxy S22+ SM-S906E U1 Firmware“.
- Use these instructions at your own risk. We will not be responsible for everything that happens to your device, resulting from using information in this guide.
- Phone must have a 70–80% charge.