Galaxy S10 SM-G973U1 U6 Firmware – Android 12 S

Galaxy S10 SM-G973U1 Binary 6 Firmware

The specific Galaxy S10 SM-G973U1 Binary 6 Firmware Download Package comes with a Stock ROM of Galaxy S10 SM-G973U1 Binary 6 Security Patch Level 2022-02-01 (February 1, 2022). This helps bypass FRP lock and revert from the root and custom ROM.

Samsung Galaxy S10 SM-G973U1 Binary 6 Android 12 United States XAA G973U1UEU6HVB2

There are various reasons to flash “Stock Firmware on Galaxy S10 SM-G973U1 Binary 6“. For example, your Phone will be stuck or hang on the logo. You want to remove the FRP lock from it.

Suppose you’re going to reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.

The Advantages Of Stock ROM:

  • Fix boot loop issue
  • Update and Downgrade
  • Unroot or Fix Bugs on the Phone
  • To solve the lag or stutter
  • Fix software issues.
  • Revert to stock firmware

Pre-requirements:

Galaxy S10 SM-G973U1 Binary 6 Stock ROM Details:

SM-G973U1 U6 United States XAA G973U1UEU6HVB2:

Model SM-G973U1 Binary 6 U6, S6, Bit 6
Region / Country United States / USA
Language Multi-Language
Android version Android 12 S
Operator / Carrier Clean XAA (no logo or carrier apps)
AP / PDA G973U1UEU6HVB2
CSC G973U1OYM6HVB2
MODEM CP Version G973U1UEU6HVB2
product code XAA
Build Date 2022-02-21
Security Patch Level 2022-02-01 (February 1, 2022)
Size 5.3 GB
[quads id=2]
Download Google Drive Android File Host

How To Install Galaxy S10 SM-G973U1 Binary 6 Stock Firmware:

1: Install the Samsung USB Driver on your pc.

2: Download and extract the  Galaxy S10 SM-G973U1 Binary 6 Firmware  files on your computer.

3: Now, Switch off your Smartphone.

4: After switching off the Phone, you need to boot into Download Mode. To boot into download mode.

Press and hold Volume Down, Home, and Power button at the same time for 5-8 seconds until download mode is active.

5: A Warning Yellow Triangle Sign appears in Download mode. Press the Volume Up key to proceed.

6: Open Odin. Then, connect your phone to the pc.

7: Odin will detect the device and show the “Added message in the lower-left panel.”.

8: Click the PDA button and select the Firmware.tar file.

9: Now, click the Start button in Odin to begin the Flashing.

10: Flashing usually takes 30-50 seconds to complete on your Phone.

Once you spot the “Pass” message in Odin, you can unplug your device from the computer.

When your Galaxy S10 SM-G973U1 Binary 6 finally boots up, you should run your desired firmware.

To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”

Disclaimer:

  • Read and understand the Full Guide before flashing.”Galaxy S10 SM-G973U1 Binary 6 Firmware.
  • Use these instructions at your own risk. We are not liable for any outcomes on your device due to following the information in this guide.
  • Phone must have a 70–80% charge.

Asim

Always had a strong interest in the Android operating system. Experience with Git and self-hosted WordPress blogs led him to the understanding that an online presence was the logical next step for his business. It's about uniqueness and individuality!

You may also like...