Galaxy Note 10+ 5G SM-N976V U7 Firmware – Android 12 S
The specific Galaxy Note 10+ 5G SM-N976V U7 Firmware Download Package comes with a Stock ROM of Galaxy Note 10+ 5G SM-N976V U7. This helps bypass the FRP lock and revert from the root and custom ROM.
Samsung Galaxy Note 10+ 5G SM-N976V Binary 7 Firmware – Android 12 S – VZW – United States – N976VVRS7GVA1
There are various reasons to flash “Stock Firmware on Galaxy Note 10+ 5G SM-N976V U7“. For instance, if your phone gets stuck on the logo and you need to remove the FRP lock from it.
If you’re going to reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.
The Advantages Of Stock ROM:
- Fix boot loop issue
- Update and Downgrade
- Unroot or Fix Bugs
- To solve the lag or stutter
- Fix software issues.
- Revert to stock firmware
Pre-requirements:
- Supported Phone: Galaxy Note 10+ 5G SM-N976V U7
- Charge your mobile: You may no less than a half charge.
- Laptop or PC.
- Backup Android Phone
- Download and install Samsung USB Driver
- Download Odin’s Latest version
Galaxy Note 10+ 5G SM-N976V U7 Stock ROM Details:
SM-N976V U7 Firmware – Android 12 S – VZW – United States – N976VVRS7GVA1
| Model | SM-N976V Binary 7 U7, S7, Bit 7 |
| Region / Country | United States |
| Language | Multi-Language |
| Android version | Android 12 S |
| Operator / Carrier | Clean (no logo, carrier apps) |
| AP / PDA | G960USQU9FUL1 |
| CSC | G960UOYN9FUL1 |
| CP Version / Baseband Modem | |
| product code | VZW |
| Build Date | 20220124082151 |
| Security Patch Level | |
| Size | 5.83 GB Full Files |
| Download | Google Drive | Mega |
How To Install Galaxy Note 10+ 5G SM-N976V U7 Stock Firmware:
1: Download and Install the Samsung USB Driver on your computer. If a Samsung USB Driver is installed on your computer, then Skip this Step.
2: Download and extract the Galaxy Note 10+ 5G SM-N976V U7 Firmware files on your computer.
3: Now, Switch off your Smartphone.
4: Turn off the phone and boot into Download Mode.
Press and hold Volume Down, Home, and Power button at the same time for 5-8 seconds until download mode is active.
5: In the Download mode, you can see a Warning Yellow Triangle Sign. In this situation, you must press the Volume Up key to continue.
6: Open Odin. Then, connect your phone to the pc.
7: Once you have connected the Smartphone to the computer, Odin will automatically recognize the device and show the “Added” message on the lower-left panel.
8: Click the PDA button and select the Firmware.tar file.
9: Now, click the Start button in Odin to begin the Flashing.
10: Flashing usually takes 30-50 seconds to complete the process on your Phone.
Once you spot the “Pass” message in Odin, you can unplug your device from the computer.
When your Galaxy Note 10+ 5G SM-N976V U7 finally boots up, you should be running your desired firmware.
To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”
Disclaimer:
- Read and understand the Full Guide before flashing.”Galaxy Note 10+ 5G SM-N976V U7 Firmware“.
- Use these instructions at your own risk. We will not be responsible for everything that happens to your device resulting from using information in this guide.
- Phone must have a 70–80% charge.
