HomeSamsungGalaxy J7 Metal SM-J710MN/DS Binary 4 Firmware – J710MNVJS4CTF2

Galaxy J7 Metal SM-J710MN/DS Binary 4 Firmware – J710MNVJS4CTF2

Galaxy J7 Metal SM-J710MNDS Binary 4 Firmware

The Galaxy J7 Metal SM-J710MN/DS is getting a Binary 4 update that just started to be updated with the 2020-05-01 (May 1, 2020) patch, but it is also bringing other improvements. the new update started to be released first in Brazil, the system is still Android 8.1.0 Oreo with customization. Security has been improved, as it now has the latest protections against the most well-known threats.

Samsung Galaxy J7 Metal SM-J710MN/DS Binary 4 Android 8.1.0 Oreo Brazil ZTO – J710MNVJS4CTF2

There are various reasons to flash “Stock Firmware on Galaxy J7 Metal SM-J710MN/DS U4“. For example, your phone will be stuck or hang on the logo. You want to remove the FRP lock from it.

If you’re going to hard reset your phone and you cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.

The Advantages Of Galaxy J7 Metal SM-J710MN/DS U4 Stock ROM:

  • Flash Stock ROM to solve the boot loop issue
  • Update and Downgrade
  • Unroot or Fix Bugs on the phone
  • To solve the lag or stutter
  • By flashing Stock ROM, you can fix software issues.
  • Revert back to stock to get your warranty.

Pre-requirements:

Galaxy J7 Metal SM-J710MN/DS U4 Stock ROM Details:

Model SM-J710MN/DS Binary 4 U4, S4, Bit 4
Region / Country Brazil
Language Multi-Language 
Android version Android 8.1.0 Oreo
Operator / Carrier Clean ZTO (no logo, carrier apps)
PDA J710MNVJS4CTF2
CSC J710MNZTO4CRK1
MODEM CP Version J710MNUBS4CTE1
product code ZTO
Build Date 19 Jun 2020
Security Patch Level 2020-05-01 (May 1, 2020)
Size 1.6 GB

Advertisment
Download Google Drive Android File Host

How To Install Galaxy J7 Metal SM-J710MN/DS U4 Stock Firmware:

Download the Odin and USB Drivers on your PC. Follow the below link to install the firmware using the Odin Flash tool.

How To Flash Samsung Stock Firmware With ODIN

1: Download and Install Samsung USB Driver on your computer. If Samsung USB Driver is already installed on your computer, then Skip this Step.

2: Download and extract the Galaxy J7 Metal SM-J710MN/DS U4 Firmware files on your computer.

3: Now, Switch off your Smartphone.

4: After switching off the phone, you need to boot into Download Mode. To boot into download mode.

Press and hold Volume Down, Home and Power button at the same time for 5-8 seconds until download mode is active.

5: In the Download mode, you will be able to see a Warning Yellow Triangle Sign. In this situation, you have to press the Volume Up key to continue.

6: Now, Download and open Odin. Then connect your Smartphone to the computer.

7: Once you have connected the Smartphone to the computer, Odin will automatically recognize the device and show the “Added” message at the lower-left panel.

8: Once Odin detects your device, click on the PDA button, and select the Firmware.tar file.

9: Now, click on the Start button in Odin to begin the Flashing.

10: Flashing usually takes 30-50 seconds to complete the process on your Phone.

Once the Firmware process is completed you will be able to see a Green Box with Pass written on it in Odin. During this process, the Smartphone will reboot automatically.

Once you see, the Pass message in Odin, you can disconnect your Device from the computer.

The flashing process will begin and should take about 10–12 minutes. It may take some time for your device to reboot, but don’t be alarmed.

When your Galaxy J7 Metal SM-J710MN/DS finally boots up, you should now be running your desired firmware.

If you want to check that the correct firmware is installed, head to Settings –> About Phone –> Software Information. The firmware number is located under the “Baseband version.”

Disclaimer:

  • Please read and understand the Full Guide before flashing “Galaxy J7 Metal SM-J710MN/DS U4 Firmware.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to your device, resulting from the use of information in this guide.
  • Before flashing, Stock ROM must have a 70–80% charge.

Related Articles

LEAVE A REPLY

Please enter your comment!
Please enter your name here

- Advertisement -

Latest Articles