Galaxy J6+ SM-J610G U6 Firmware – J610GUBU6CUE1

SM-J610G Binary 6 Firmware – J610GUBU6CUE1

The specific Galaxy J6+ SM-J610G U6 Firmware Download Package comes with a Stock ROM of Galaxy J6+ SM-J610G U6 Security Patch Level 2021-04-01 (April 1, 2021). This helps you to bypass the FRP lock and revert from the root and custom ROM.

Samsung Galaxy J6+ SM-J610G Binary 6 Android 10 Q Brazil ZTO – J610GUBU6CUE1

There are various reasons to flash “Stock Firmware on Galaxy J6+ SM-J610G U6“. For instance, if your phone gets stuck on the logo and you need to remove the FRP lock from it.

If you’re going to reset your phone hard and cannot access the recovery menu. But most of the problems that cause flashing stock ROM are below.

The Advantages Of Stock ROM:

  • Fix boot loop issue
  • Update and Downgrade
  • Unroot or Fix Bugs
  • To solve the lag or stutter
  • Fix software issues.
  • Revert to stock firmware

Pre-requirements:

Galaxy J6+ SM-J610G U6 Stock ROM Details:

SM-J610G U6 Brazil ZTO – J610GUBU6CUE1:

Model SM-J610G Binary 6 U6, S6, Bit 6
Region / Country Brazil
Language Multi-Language
Android version Android 10 Q
Operator / Carrier Clean ZTO (no logo, carrier apps)
PDA J610GUBU6CUE1
CSC J610GOWO6CUE1
MODEM CP Version J610GUBU6CUD5
product code ZTO
Build Date Tue, 04 May 2021
Security Patch Level 2021-04-01 (April 1, 2021)
Size 2.6 GB
[quads id=2]
Download Google Drive Android File Host
SM-J610G U6 Panama PBS – J610GUBU6CUG1:
Model SM-J610G Binary 6 U6, S6, Bit 6
Region / Country Panama
Language Multi-Language
Android version Android 10 Q
Operator / Carrier Clean PBS (no logo, carrier apps)
PDA J610GUBU6CUG1
CSC J610GOWT6CUD5
product code PBS
Build Date 05 Jul 2021
Security Patch Level 2021-07-0 (July 1, 2021)
Size 2.7 GB
Download 2File Google Drive

How To Install Galaxy J6+ SM-J610G U6 Stock Firmware:

1: Install the Samsung USB Driver on your pc.

2: Download and extract the Galaxy J6+ SM-J610G U6 Firmware files on your computer.

3: Now, Switch off your Smartphone.

4: Turn off the phone and boot into Download Mode.

Press and hold Volume Down, Home and Power button at the same time for 5-8 seconds until download mode is active.

5: A Warning Yellow Triangle Sign appears in Download mode. Press the Volume Up key to proceed.

6: Open Odin. Then, connect your phone to the pc.

7: Odin will detect the device and show the “Added message in the lower-left panel.”.

8: Click the PDA button and select the Firmware.tar file.

9: Now, click the Start button in Odin to begin the Flashing.

10: Flashing usually takes 30-50 seconds to complete on your Phone.

Once you spot the “Pass” message in Odin, you can unplug your device from the computer.

When your Galaxy J6+ SM-J610G finally boots up, you should run your desired firmware.

To verify the installed firmware, go to Settings –> About Phone –> Software Information. Check the firmware number under “Baseband version.”

Disclaimer:

  • Read and understand the Full Guide before flashing.”Galaxy J6+ SM-J610G U6 Firmware.
  • Use these instructions at your own risk. We are not liable for any outcomes on your device due to following the information in this guide.
  • Phone must have a 70–80% charge.